Somerset - Air Pressure Testing - 01752 687 017

The office that covers this area is: Plymouth

The towns & cities that are covered within this county are:
Axbridge, Bridgwater, Bruton, Burnham on Sea, Castle Cary, Chard, Cheddar, Crewkerne, Dulverton, Dunster, Exford, Farrington Gurney, Frome, Glastonbury, Highbridge, Hinton St George, Ilchester, Ilminster, Langport, Long Sutton, Martock, Meriott, Midsomer Norton, Minehead, Montacute, Porlock, Radstock, Shepton Mallet, Shoreditch, Somerton, South Petherton, Sparkford, Stoke Sub Hamdon, Street, Taunton, Watchet, Wellington, Wells, Williton, Wincanton, Winsford, Yatton, Yeovil,

Phone Number: 01752 687 017 Email: somerset@e2consultants.co.uk

Somerset - Air Pressure Testing

Our air consultants offer constructive advice on what is the best way to reach your target rating. The table below shows the number of air tests you may require:

At E2 Consultants we offer Air Pressure Testing throughout Somerset and surrounding areas. Our experienced Air Pressure Testing assessors will also be happy to offer advice on the best ways to gain your target rating. The number of properties to be tested should be in accordance with the following table:

According to Part L1a, an air pressure test needs to be undertaken on 50% of all dwelling types or three units of each type depending on which value is smaller. A block of flats is considered as a separate development and should be treated as such no matter on the number of blocks on the site. Furthermore, the testing should be done on the first batch of each type of dwelling to be completed. The need to test multiple versions of each type is to confirm the design and construction procedures are up to code according to Government regulations.

The dwellings that make up the test sample are to be chosen by the Building Control Body (BCB) as well as the pressure tester. When selecting the dwellings it should be taken into account that half of the tests for each type should be scheduled during construction of the first 25% of that type. All results, including failures, should be reported back to the BCB. Undertaking the test early in the project means any adjustments can be made before the majority of construction is complete.

It is a requirement under the Building Regulations 2015 Part L that new dwellings in Somerset must pass an Air Pressure Testing prior to occupation; this test certificate must be produced for the dwelling to be signed off by local Somerset building control.

The report has all the details required by the regulations to indicate that a valid test has been performed.

To carry out such a test with accurate results, we require some general requirements to be made available at the time of the test:

1. SAP Design air pressure test figure

2. Electricity supply

3. Water supply to enable traps to be filled

We will seal all of the intentional leakage areas in the house prior to testing. These include: fireplaces, extractor fans, exhaust fans, trickle vents and the odd uninstalled component. Everything else will have to stay 'as is' in the property.

It's strongly suggested that if you've never had a test before, that you review our air pressure / tightness pre-test checklist below.

Air Tightness Pre-Test Checklist

For a quote or for more information, call our Somerset air tightness / pressure testing consultant on 01752 687 017 or email somerset@e2consultants.co.uk
Warning: count(): Parameter must be an array or an object that implements Countable in /data04/elite/public_html/Office.php on line 755

For further Air Pressure Testing information for your area, be sure to check out Air-Testing-Plymouth.co.uk.

Our other services include:

Air Pressure Testing can also be known as:
Commercial Fan Pressure Testing, Commercial Air Integrity Testing, Commercial Air Tightness Testing, Air Testing, Commercial Air Leakage Testing, Commercial Air Pressure Testing, Commercial House Leakage Testing, Air Tightness Testing, Air Leakage Testing, Commercial Air Testing, Fan Pressure Testing, Air Integrity Testing, House Leakage Testing,